I just got back home after *way* too long away, and when I plugged the computer into the Belkin router via the cable, eth0 failed to connect. I had used the cable before, and I even unplugged the cable from the laptop and plugged the cable into the desktop, worked fine, so it is not the cable. ...
Honestly it is possible that I never had to reboot it once configured until recently when I discovered that after rebooting the eth0 did not come up at boot. ...
Ubuntu Linux: Creating ethernet alias for eth0 network device ... Q. I am using Ubuntu Linux and I would like to know how to create alias for eth0 so that I can have multiple IP address? ...
Can't exec /etc/mrtg/eth0.sh: No such file or directory at /usr/bin ... WARNING: Running '/etc/mrtg/eth0.sh /proc/net/dev': No such file or directory ...
Defining physical interfaces such as eth0. Lines beginning with the word auto are used ... auto eth0 # iface eth0 inet manual # up ifconfig $IFACE 0.0.0.0 up # up ip link set ...
auto eth0 iface eth0 inet static address 192.168.1.1 netmask 255.255.255.0 gateway 192.168.1.254 broadcast 192.168.1.255 dns-nameservers 192.168.1.254. Then if you have previously used DHCP then until you reboot dhclient will still be running and so you should kill it: ...
In a nutshell, this post will explain how you can ensure traffic going into eth0 goes out only on eth0, as well as enforce all traffic going into eth1 goes out only on eth1. You've found the one post that actually explains this issue; your googling has paid off. ...
RE: [linux] Connecting via modem after forever via eth0. On Sep 1, Meph Istopheles tapped one key, than another, then another... Re: Connecting via modem after forever via eth0 ... Hash: SHA1 Being connected to the shell is just like ...
If you have set eth0:0 on a different IP block and you want it to still be able to communicate with eth0:1 IP block you will need to add route on the routing table. ...
So that when I create a vmware guest I can choose eth0/eth1 to be bridges to the /dev/vmnet2 or so forth, and know that specific interface will be on a particular vlan. ... Then running brctl addbr br0 ; brctl addif br0 eth0² to produce the bridge and starting the domain again allows life to continue ...
Listen On Eth0: ... Listen On Eth0 #1 Markoetie. Newbie. Group: Members. Posts: 1. Joined: 29-September 09. Posted 29 September 2009 - 01:28 PM. Hi, I'm running monyog on Linux and I want to reach Monyog over the net but I can't because by default it listens on 127.0.0.1. ...
After installation was complete I found that while on three systems networking worked fine, on the fourth I could not bring up eth0, which gave the error: ... forcedeth: using HIGHDMA eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:07.0 eth1394: eth0: IEEE-1394 IPv4 over 1394 ...
A PREROUTING -i eth0 -p tcp -m tcp --dport 41001 -j LOG --log-prefix H015 -t:nat: ... H015 -t fwd tcp41001 dport IN=eth0 OUT=eth1 SRC=87.227.31.20 DST=10.1.1.15 LEN=60 TOS=0x00 PREC=0x20 TTL=41 ID=20327 DF PROTO=TCP ...
Photo courtesy of new1mproved This article is written by Lakshmanan G Ifconfig command is used to configure network interfaces. ifconfig stands for ... ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:2D:32:3E:39:3B inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80: ...
Now we want to use the IP address 192.168.0.101 on the virtual interface eth0:0. Therefore we open the file /etc/sysconfig/network-scripts/ifcfg-eth0:0 and modify it as follows (we can leave out the HWADDR line as it is the same physical network card) ...
This morning I encountered a problem trying to setup IP masquerading with my ASUS notebook. Notebook has only one network interface and it is connected to my ... ifconfig eth0:1 192.168.0.1 netmask 255.255.255.0 ...
The original Xircom-based card started out as eth0, the Linksys WPC11 was eth1, the ASIX-based wired card was eth2, and so forth. ... Anyway, it was easy enough to comment out the offending lines in that file, and after rebooting, the sequence started over again at eth0. ...
Camouflage everything what leaves by eth0 to the outside ... t nat -A POSTROUTING -o eth0 -j MASQUERADE # We allowed the nonprivileged users to accede ...
default 192.168.178.1 0.0.0.0 UG 0 0 0 eth0. Well everything seems to work, pings on all ips and dns resolution BUT if i visit whatismyip.com or sth. like that, it just shows me my DSL providers ip and country, so it is just dont using the vpn. I dont understand why! ...
note that in the if statement you have to enclose the variable in double quotes because the line repeated by $eth0 contains whitespaces ... Test for pppoe connectivity since both ppp0 and eth0 are up ...
linux (19)
ip address (13)
ifconfig eth0 (12)
interface (11)
server (11)
how to (10)
eth1 (9)
ifconfig (8)
network interface (8)
ubuntu (6)
iface (6)
ip (6)
netmask (6)
mac address (6)
sudo (5)
usr (5)
setup (5)
dhcp (5)
inet (4)
sbin (4)
gw (4)
flags (4)
broadcast (4)
udev (4)
nic (4)
the network (4)
ubuntu linux (4)
kernel (4)
configure (4)
gender (4)
dhcp server (4)
fedora (4)
br0 (4)
bridge (4)
ttl (3)
iphone (3)
firewall (3)
vlan (3)
auto (3)
the bridge (3)